DOC HOLLIDAY MOLDS

• 1. Identification of Preparation - Company

• Product Identity Numbers  Designer Glazes DG-20l through DG-221
• Classic Glazes CG-300 through CG-311

2. Composition

Component              C.A.S.       EINECS                   % of Composition

Crystalline Silica     7631-86-9  2315454                     less than 10%

Unleaded Frit &

naturally occurring                                                    rest ( 90% + )

minerals

3. Hazardous Identification

Inhalation: In liquid state there is no known hazard, however if dry spillage or sprayed, excessive dust inhalation may result in respiratory disease, including silicosis, pneumoconiosis and pulmonary fibrosis. DO NOT AIRBRUSH OR SPRAY.

4. Emergency and First Aid Measures

• Excessive Inhalation:   Remove to fresh air loosen clothing and resuscitate if required.
• Ingestion:                   Do not induce vomiting, seek medical advice.
• Eyes:                         Flush immediately with quantities of water.
• Skin:                          Wash affected areas with water.

5. Fire-fighting Measures

Extinguishing Media: Suitable for surrounding fire conditions Water CO2 or dry chemicals.

• Flash point             - none. Will not burn
• LEL                       - not applicable
• Flammable limits    - not applicable
• UEL                       - not applicable

Special Fire Fighting Procedure: None, except plastic storage containers. Wear self contained breathing apparatus

Unusual Fire and Explosion Hazards: Burning plastic containers may cause hazardous fumes.

6. Accidental Release Measures

Leaks and Spills: Wipe up spillage then clean with soap and water. As this product is not considered a hazardous waste, dispose of in accordance with Local Authority Regulations.

7. Handling and Storage

• Handling: Do not eat, drink or smoke in areas where this material is used. Wash hands thoroughly after handling the product.
• Storage: Do not allow to freeze.

8. Exposure Controls / Personal Protection

• Engineering Controls: Adequate ventilation should be provided so the Occupational Exposure Limits are not exceeded. Local Exhaust Ventilation is preferable to personal protection.
• Personal Protection: Where necessary suitable personal protection should be used. (e.g. aprons, gloves).

9.Physical and Chemical Properties

• Specific Gravity: 1.4 – 1.6
• Melting Point in excess of 540°C 1000°F
• Solubility in Water: Insoluble
• Vapor Pressure: Not applicable
• Vapor Density: Not applicable
• Evaporation Rate: Not applicable
• Boiling Point: Not applicable
• Appearance: Aqueous Solution
• Color: Variable
• Odor: Virtually Odorless

10.Stability and Reactivity

• Stability: This product is stable
• Conditions to Avoid: None known
• Incompatibility
• (Materials to Avoid): None known
• Hazardous Decomposition
• of By products: Fire may cause hazardous fumes from burning plastic
• Hazardous Polymerization: None

11.Toxicological Information

13. Disposal of Product

As the product is not hazardous, Local Authority waste disposal regulations are appropriate.

14. Transport Information

• U.N./S.I. No         Not restricted
• U.N. Class           Not restricted
• Packing Group     Not restricted
• Air: I.C.A.O.         Not restricted
• Sea:I.M.O.           Not restricted
• Road: A.D.R.       Not restricted
• U.K.                    Not restricted

15. Regulatory Information

• EC Supply Labeling: None required by directive 88/379/EEC and subsequent amendments.
• A.S.T.M. D-4236: Conforms

16. Other Information:

Do not eat, drink or smoke when using product, do not breath spray. This product should not be sprayed

Since the specific conditions of use of the product are outside the control of the supplier, the user is responsible for ensuring that the requirements of relevant legislation are complied with. The information within this safety data sheet is correct to the best of our knowledge at the date of publication. The information applies only to the specified products designated and may not be valid for the product if used in combination with any product or process other than specified in the test.